ADVrider

Go Back   ADVrider > Search Forums
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Showing results 1 to 17 of 17
Search took 0.00 seconds.
Search: Posts Made By: Kleio
Forum: Thumpers 04-27-2013, 08:18 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
I moved the clip on the needle to the highest...

I moved the clip on the needle to the highest (first) slot and now my DR200SE runs much better.:clap The exhaust is much cleaner. The idle is much crisper and doesn't die at stop lights. The engine...
Forum: Thumpers 04-23-2013, 08:43 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
I perused the internet and I found out that the...

I perused the internet and I found out that the air/fuel mixture can be made leaner by moving the clip on the needle up. I currently have it set on the third notch as it as sent to me by Kientech.
...
Forum: Thumpers 04-22-2013, 09:32 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Took the carb apart today and the washer (it is...

Took the carb apart today and the washer (it is not an O-ring) is on the main jet, so that is not the problem.

One last thing, when I ordered the jet kit I asked if it was necessary to have the...
Forum: Thumpers 04-21-2013, 11:35 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
I'm sure I assembled the pilot screw correctly. ...

I'm sure I assembled the pilot screw correctly.

I didn't notice an O-ring above the main jet. If I lost that, then I'm SOL. I can't even go back to the original main jet if I wanted to. Oh...
Forum: Thumpers 04-21-2013, 10:33 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
I replaced the needle per the instructions I...

I replaced the needle per the instructions I received from Kientech.

I did not take the floats off. I replaced the main jet and the pilot jet inside the bottom of the carb. I also replaced the...
Forum: Thumpers 04-21-2013, 09:09 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Continuing problems with Kientech jets

As I wrote in an earlier post, after installing the Kientech jets and needle, the engine would "cut out"/"miss". Upon further investigation, this was probably due to a fouled up spark plug. I...
Forum: Thumpers 04-20-2013, 12:10 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Turning the fuel screw had no effect on the idle...

Turning the fuel screw had no effect on the idle speed (besides burning the back of my hand several times. :pissed)

Any suggestions on what I am doing wrong?:hmmmmm

Thanks.
Forum: Thumpers 04-14-2013, 08:33 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
This sounds like this may be related to another...

This sounds like this may be related to another problem I was having. From a standing stop in 1st gear, when I let out the clutch and started to go the engine would start sputtering and I would have...
Forum: Thumpers 04-14-2013, 04:16 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Installed Kientech jet kit. Questions.

I installed the Kientech jet kit yesterday. All in all, not too difficult.

The process was made easier by looking at the diagram in this link...
Forum: Thumpers 04-08-2013, 10:01 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Thanks again. I feel more confident now. I'll...

Thanks again. I feel more confident now. I'll try to install the jet kit this coming weekend. I'll let you know how it turns out.

Regarding the exhaust, I've decided to wait until next winter...
Forum: Thumpers 04-08-2013, 09:40 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Thanks for your quick response! On one of...

Thanks for your quick response!

On one of the photographs they show the tip of fuel screw "tower" being "trimmed" with a hack saw blade. Is this how you did it? Is it possible to use a Dremel...
Forum: Thumpers 04-08-2013, 08:53 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Eh? Wanted: Instructions for installing Kientech jet kit

Just received the Kientech jet kit in the mail and I am surprised at the sparse instructions that came along with it.

There are five pages, each with a black and white photograph and some text...
Forum: Thumpers 03-23-2013, 10:57 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
When you shipped it to Kientech, how did you box...

When you shipped it to Kientech, how did you box it? Did you happen to have a box with the correct dimensions? Did you have to add the packing peanuts?

Sorry to be asking so many questions, but...
Forum: Thumpers 03-23-2013, 08:39 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
Kientech stock exhaust mod

<style type="text/css">P { margin-bottom: 0.08in; }</style> Has anyone had the Kientech stock exhaust mod done?


How did you ship your exhaust to them (UPS, FedEx)? How did you package it?...
Forum: Thumpers 01-25-2013, 07:35 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
DG pipe

I've read that the DG exhausts are very loud. Do you think yours is very loud?

I'm thinking of upgrading the exhaust but find that the FMF Q4 is very expensive. The DG is at a better price...
Forum: Thumpers 01-16-2013, 08:06 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
I found it at a dealership in Fremont, CA. They...

I found it at a dealership in Fremont, CA. They told me that the previous owner had traded it in along with a Yamaha scooter for a Royal Enfield. I negotiated a bit and I got a base price of...
Forum: Thumpers 01-15-2013, 09:01 PM
Replies: 9,008
Views: 1,280,880
Posted By Kleio
New Member

Hello. Last month I purchased a used 2009 DR200SE with only 21 miles on it.

I used to ride a Bridgestone 90cc bike when I was in high school in the early '70s. I'm now 57 and I wanted to ride...
Showing results 1 to 17 of 17

 
Forum Jump

Times are GMT -7.   It's 10:46 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014