Paid $300 with a coupon . Lucky to get one , they sell as soon as the truck delivers to the store in Norfolk . I am really impressed how sturdy it is . I upgraded to a better wheel chock . I installed it with 3/8 carriage bolts with wing nuts so I can remove it if I need to do fork work etc... The supplied wheel lock looked very sketchy . A vise like clamp that I wouldn't trust to hold a bicycle . btw: for the Harley haters , that is a permanent stain on the floor, not oil ....lol .. .. .. .
Do you think this table (with the better front wheel chock) would handle a full dress harley? FLHTCUI Seems like it would be maxed out...
1000 lb capacity , it's very sturdy , however it's narrow and you are at least 5 inches off the floor once you drive up the ramp . Not much room for feet or a misstep . You could walk it up but I wouldn't do it without help . I was nervous the first time I drove my Sportster on it . I upgraded the wheel chock so I could dismount without worry prior to strapping . A Sportster is around 540# , a bagger is maybe 700+ . It has 2 locking positions . I used a wheeled stool to work on my exhaust in the lower position & the bike felt rock solid up there .
Please note : That wheel chock I used has 3 positions so it's best to try it out on the ground because once the front wheel gets trapped it might be tough to back out because you might be too high or too low . Temp screw it down on a piece of plywood to find that sweet spot . If not held down it may roll back with you and jack up that nice front fender or come damn close ...lol
Yep -- if you watch the coupons in the moto-mags, you can get that gray chock for $25. I have two in my trailer -- simple, cheap, strong, crude. What more do you need? Just roll the bikes in, then strap 'em down at your leisure.
Here is the DR on the HF lift. DR had been stored 1/2 outside for 3 years, this is it starting the go through. Gas, carb clean and a battery is all it needed. Now it has much more . I have the front wheel squeezing clamp which is ok for keeping the wheel straight when strapped down but is a pain in the butt when loading a bigger bike so I think I'll replace it with a chock I can roll the bike onto. I dropped a Bimota once :eek1
those bikes are almost bullet proof . take a ton of abuse . I have to figure a way to get crankshaft access cover off . Previous owner tried with an Allen that was 2 sizes too small & rounded it out really nice . Have a new one from ProCycle . Need to get in there to adjust valves . ..
I've wanted one of those Infrared Thermometers for a long time. Bought the Cen-Tech from Harbor Freight for $49.95. Works great. Mail ordered this because I was just not in a hurry to get it. Well it was slow but we just had Xmas and I was happy with it anyway. I'll be able to tell how the AC is doing next season. Yeah.
The bike I am currently restoring has a nasty dent in the tank and the next bike I will be doing has a shallow cave in on one whole side so decided to try the harbor freight stud welder kit I am not a fan of harbor freight and at 50 years old and a lifle long tool junkie this is actually the first harbor freight tool purchase for me. the kit comes with the welder and two different size tips and a handfull of studs for each tip and a slide hammer designed to work with the studs. The welder works perfectly with both size studs and the tips are easy to change. The online reviews for the slide hammer were almost unanamous in their opinion that the slide hammer didn't work. I had zero problems with the slide hammer on the small studs but had a bit of a problem with it on the larger studs. I did eventualy figure out that if I held the locking cam with my finger for the first few hit with the slide that I could get the hammer to grip the larger studs about 95% of the time I'm sure with a bit of re engineering and a file the locking cam could be improved but for the ocasional use it will get in my shop it is fine as is. I paid $99 for the kit on sale but even for the regular price I think this tool is a great value for the time it can save.
For $9.99 a pop these cant be beat. I mean they click when they get to what you set them too, what more can you ask? Pass. Ended up getting all 3 sizes.
At a small car and scooter sales place i used to work at, we had one of these lifts for working on the scooters, had a guy bring in an ElectraGlide for an oil change. We had one guy duckwalk the bike onto the lift under engine power and another to strap it down before he got off, it lifted it up and we did the oil change. Would I recommend doing heavy wrenching on a bike that big on it , but for oil changes and stuff it would be fine.
:huh I don't think it makes a difference what you are doing to the bike. (oil change/valve job) The table is doing the same job regardless of what you are doing to the bike. It works fine. I have no issue loading a Concours 14 on it myself with the stock wheel clamp.
I have a few various tools that have held up well, the Pittsburg hand tools sure aren't Snap-On, but I have yet to break one. The ratcheting box-end wrenches are super practical, and I've gotten good use out of them. OTOH, every time I go to HF, someone is returning an electric tool of some sort that didn't work, or stopped working. The best thing I ever bought there is a mechanic's stool... my knees thank me every time I use it. http://www.harborfreight.com/mechanics-roller-seat-3338.html
I bought 4 HB machete's and although they took 4 weeks to get here, I love them! Gave 3 as gifts and kept one myself. I polish one to almost a mirror finish and sharpened it to a pretty good edge.
I have that same stool. Use it all the time. Have bought a lot of things from HF. Can't bring myself to buy their screwdrivers though. The 1/2" electric impact is w/o a doubt my favorite. Every time I use it I'm glad I bought it.