Any Honda Dominator NX650 owners out there ? - Page 168

Skapegoat · 11-12-2012, 05:11 PM

I was wondering why my dominators rear running light wasn't working...
I thought it may have been the bulb but it wasn't.
The bulb housing has literally just corroded away so some genius had Sellotaped the bulb in place.
Off to the breakers to mo to see if they have a replacement!

Notice the rusting and rotting brown parts.

Sierra Thumper · 11-12-2012, 07:05 PM

Quote:

Originally Posted by Skapegoat

I was wondering why my dominators rear running light wasn't working...
I thought it may have been the bulb but it wasn't.
The bulb housing has literally just corroded away so some genius had Sellotaped the bulb in place.
Off to the breakers to mo to see if they have a replacement!

Notice the rusting and rotting brown parts.

Just Mother Nature reclaiming what is hers

dstriffler · 11-13-2012, 08:38 AM

It seems like every bike has some botched up repair job from a previous owner. While I'm working on removing the stain from the speedo plastic, does anyone know to remove this? It appears to be some type of cement holding the bottom of the fairing to the mount. The key is to remove it without damaging the rest of the plastic. I used a grinder to grind it down a lot, but I still have this blocking me from mounting the plastic air guide. I was hoping some kind of solution soak would dissolve it, but not remove the paint from the fairing. If not I suppose I can leave it there and just drill a hole through it. But if something will remove it that would be great, because the previous owner also decided to use this all over the carb to stop a leak. I already installed a brand new XR650 carb, but I still have the old carb, and I'd still like to get it off. I'm also thinking I might find this elsewhere on the bike.

Timieh · 11-14-2012, 08:04 AM

Dear Friends

I don't know what to do next

My other engine of my domi got it complete with a new piston etc.
But 1000km later it also cracked and I was grinding over the floor.

But now I don't trust that engine anymore because it is the 2nd time. So I bought an other Domi for parts and stuff.
And used up the Engine, Everything worked fine until I needed to pull out the air out of the oil pump......
Tryed several things, Now the pump do pump oil throught the under channel [not the left one] So i mounted my oil filter back in place loosen the banjo at the top and started it on the startmotor, No oil coming out. and the battery was getting empty.

Charged it up for 1 day.

The other day I checked again there was oil coming from below, layed down my motorcycle, put the oil filter compartment full of oil, so there is no air inside it. Put my motorcycle upright started it

Waited for some time around 40sec. And there is also no oil comming out off the top.

What to do

The only thing I can think, remove the pump from the engine aind do it like the manuel :S

FLICKIT · 11-14-2012, 12:18 PM

Check the rubber hoses that go from the frame tank to the engine, I have read that can get kinked and blocked off...

Also, if you haven't removed/cleaned the fitting and screen from the bottom of the frame oil tank, it might be worth doing...

There's a vent pipe that goes from the rocker/valve cover to the frame oil tank, I removed that from the rocker cover and put a little air pressure on it to pressurize the oil tank and force the oil through... With a small amount of air pressure, the engine only needed cranking over a few times before the oil is coming out the banjo fitting on the head...

Good luck :)

Edit:

Timieh · 11-14-2012, 01:15 PM

Have tried it with a bicycle pump, That needed to be enough pressure.

But I only did it to control if there is oil coming inside the oil compartment. and that does.
But when i close it up. It aint reaches my head :S ?

Skapegoat · 11-15-2012, 11:21 AM

Recovered my seat today!

It went from this....

To this...

First time covering a seat it's not perfect but better than it was!
And I only stapled myself 213 times

Timieh · 11-16-2012, 12:30 AM

It looks you did a good job

Skapegoat · 11-16-2012, 06:51 AM

Quote:

Originally Posted by Timieh

It looks you did a good job

Thanks, it looks better in the photos than real life.
My only tips are put a black sack bin liner under the cover to help it slide on and to start from the front.
Also USe an electric staple gun.

Bounder · 11-16-2012, 02:03 PM

Heating the vinyl with a hairdryer makes it easy to stretch as well.
I use a Black and Decker Power shot stapler, its not electric but it puts the weight forward when you use it, not at the back.
I also use stainless staples.
I'll be redoing one soon, as soon as I decide what colour I'll be going with......

Timieh · 11-19-2012, 07:33 AM

Pretter handy,

But does someone god the whole one, only found a part of it and nog looking great

dstriffler · 11-20-2012, 04:51 AM

Imagine if these were NX650's

http://cgi.ebay.com/ebaymotors/2-TWO...item43b611695a

Skapegoat · 11-20-2012, 02:31 PM

Quote:

Originally Posted by dstriffler

Imagine if these were NX650's

http://cgi.ebay.com/ebaymotors/2-TWO...item43b611695a

Great find, buy them!

sw3dl1 · 11-21-2012, 04:14 AM

Or even 250's

Quote:

Originally Posted by dstriffler

Imagine if these were NX650's

http://cgi.ebay.com/ebaymotors/2-TWO...item43b611695a

Slim-Line Tonic · 11-21-2012, 03:23 PM

got me one too!! an old 89 with a lot of km's (65k)

IMG00074-20121120-1132 by MACK1869, on Flickr

need to get a higher screen too, to get more wind protection...

IMG00075-20121120-1143 by MACK1869, on Flickr

And a mirror too, but i think the screwing bracket is broken too :-s

11-14-2012, 08:04 AM	#2509
Timieh Adventurer Joined: Jul 2012 Location: Nehterlands Oddometer: 28	Dear Friends I don't know what to do next My other engine of my domi got it complete with a new piston etc. But 1000km later it also cracked and I was grinding over the floor. But now I don't trust that engine anymore because it is the 2nd time. So I bought an other Domi for parts and stuff. And used up the Engine, Everything worked fine until I needed to pull out the air out of the oil pump...... Tryed several things, Now the pump do pump oil throught the under channel [not the left one] So i mounted my oil filter back in place loosen the banjo at the top and started it on the startmotor, No oil coming out. and the battery was getting empty. Charged it up for 1 day. The other day I checked again there was oil coming from below, layed down my motorcycle, put the oil filter compartment full of oil, so there is no air inside it. Put my motorcycle upright started it Waited for some time around 40sec. And there is also no oil comming out off the top. What to do The only thing I can think, remove the pump from the engine aind do it like the manuel :S __________________ Trying my best words of English. Honda NX 650 RD08 1996 Dominator Timieh screwed with this post 11-14-2012 at 10:01 AM

11-14-2012, 12:18 PM	#2510
FLICKIT Gnarly Adventurer Joined: Aug 2011 Location: Down-under Down-under Oddometer: 471	Check the rubber hoses that go from the frame tank to the engine, I have read that can get kinked and blocked off... Also, if you haven't removed/cleaned the fitting and screen from the bottom of the frame oil tank, it might be worth doing... There's a vent pipe that goes from the rocker/valve cover to the frame oil tank, I removed that from the rocker cover and put a little air pressure on it to pressurize the oil tank and force the oil through... With a small amount of air pressure, the engine only needed cranking over a few times before the oil is coming out the banjo fitting on the head... Good luck :) Edit: FLICKIT screwed with this post 11-14-2012 at 12:39 PM

11-14-2012, 01:15 PM	#2511
Timieh Adventurer Joined: Jul 2012 Location: Nehterlands Oddometer: 28	Have tried it with a bicycle pump, That needed to be enough pressure. But I only did it to control if there is oil coming inside the oil compartment. and that does. But when i close it up. It aint reaches my head :S ? __________________ Trying my best words of English. Honda NX 650 RD08 1996 Dominator

11-16-2012, 12:30 AM	#2513
Timieh Adventurer Joined: Jul 2012 Location: Nehterlands Oddometer: 28	It looks you did a good job __________________ Trying my best words of English. Honda NX 650 RD08 1996 Dominator

11-19-2012, 07:33 AM	#2516
Timieh Adventurer Joined: Jul 2012 Location: Nehterlands Oddometer: 28	Pretter handy, But does someone god the whole one, only found a part of it and nog looking great __________________ Trying my best words of English. Honda NX 650 RD08 1996 Dominator

11-12-2012, 05:11 PM	#2506
Skapegoat Adventurer Joined: Sep 2012 Location: Ireland Oddometer: 37	I was wondering why my dominators rear running light wasn't working... I thought it may have been the bulb but it wasn't. The bulb housing has literally just corroded away so some genius had Sellotaped the bulb in place. Off to the breakers to mo to see if they have a replacement! Notice the rusting and rotting brown parts.

11-13-2012, 08:38 AM	#2508
dstriffler Gnarly Adventurer Joined: Jul 2012 Location: New York Oddometer: 133	It seems like every bike has some botched up repair job from a previous owner. While I'm working on removing the stain from the speedo plastic, does anyone know to remove this? It appears to be some type of cement holding the bottom of the fairing to the mount. The key is to remove it without damaging the rest of the plastic. I used a grinder to grind it down a lot, but I still have this blocking me from mounting the plastic air guide. I was hoping some kind of solution soak would dissolve it, but not remove the paint from the fairing. If not I suppose I can leave it there and just drill a hole through it. But if something will remove it that would be great, because the previous owner also decided to use this all over the carb to stop a leak. I already installed a brand new XR650 carb, but I still have the old carb, and I'd still like to get it off. I'm also thinking I might find this elsewhere on the bike.

11-15-2012, 11:21 AM	#2512
Skapegoat Adventurer Joined: Sep 2012 Location: Ireland Oddometer: 37	Recovered my seat today! It went from this.... To this... First time covering a seat it's not perfect but better than it was! And I only stapled myself 213 times

11-16-2012, 02:03 PM	#2515
Bounder Gnarly Adventurer Joined: Mar 2011 Location: West Cork, Ireland Oddometer: 411	Heating the vinyl with a hairdryer makes it easy to stretch as well. I use a Black and Decker Power shot stapler, its not electric but it puts the weight forward when you use it, not at the back. I also use stainless staples. I'll be redoing one soon, as soon as I decide what colour I'll be going with......

11-20-2012, 04:51 AM	#2517
dstriffler Gnarly Adventurer Joined: Jul 2012 Location: New York Oddometer: 133	Imagine if these were NX650's http://cgi.ebay.com/ebaymotors/2-TWO...item43b611695a

11-21-2012, 03:23 PM	#2520
Slim-Line Tonic Adventurer Joined: Oct 2012 Location: Rider's Riviera Oddometer: 35	got me one too!! an old 89 with a lot of km's (65k) IMG00074-20121120-1132 by MACK1869, on Flickr need to get a higher screen too, to get more wind protection... IMG00075-20121120-1143 by MACK1869, on Flickr And a mirror too, but i think the screwing bracket is broken too :-s

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: .
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode