XR400 Four - Skunkworks Special - Page 31

Pezz_gs · 01-16-2013, 03:24 AM

Another

Pezz_gs · 01-20-2013, 06:23 PM

Just found another pic of it, a bit arty

Pezz_gs · 02-11-2013, 02:31 PM

Time for some more work on Yajuu

I need to do something serious about the front brakes on this bike

Current front end is XR/XL 250 Disc brake set up. 38mm forks Honda XR-250R (84-85)

Question is, what will fit on here Disc wise and calliper wise?

I can fabricate an adapter bracket for a calliper if needed.

Or what else runs 38mm forks, that would be suitable for a swap over?

Looking at the thread below, not much on offer in 38's

http://www.advrider.com/forums/showp...&postcount=198

kellymac530 · 02-11-2013, 08:28 PM

Disc is gonna be a bit trial and error. 4 bolt rotor, I think newer Kawasaki KXf bikes are 4 bolt. not sure if it is the same pattern and bolt centerline though.
Caliper wise, about ANYTHING newer will work better but you will need to make an offset for the bigger rotor. The master cylinder may also be an issue though, getting the right MC bore and caliper piston size ratio is critical.

Rotor diameter is probably the biggest issue, that thing is a tea cup saucer, you need a dinner plate.

doug s. · 02-11-2013, 08:36 PM

Quote:

Originally Posted by Pezz_gs

Time for some more work on Yajuu

I need to do something serious about the front brakes on this bike

Current front end is XR/XL 250 Disc brake set up. 38mm forks Honda XR-250R (84-85)

Question is, what will fit on here Disc wise and calliper wise?

I can fabricate an adapter bracket for a calliper if needed.

Or what else runs 38mm forks, that would be suitable for a swap over?

Looking at the thread below, not much on offer in 38's

http://www.advrider.com/forums/showp...&postcount=198

this one indicates it will fit '84-'04, but the link to the bracket is iffy, re: fitment - likely the same rotor w/different caliper for later years?
270 mm rotor:
http://www.ebay.com/itm/271017502421
bracket:
http://www.ebay.com/itm/271019077275

320mm rotor bracket (rotor will fit, but not the bracket?):
http://www.ebay.com/itm/320974991593

doug s.

NordieBoy · 02-15-2013, 07:41 PM

Pre 2008 KLR650?

Pezz_gs · 03-10-2013, 08:54 PM

Well I just went out, after having the heli-coil inserted to secure Number 4 spark plug, just gave it a kick in the guts

NordieBoy · 03-10-2013, 10:43 PM

That, is the coolest sounding starter in the history of the world.

Made by Nippon-Denso-Hyena?

Pezz_gs · 03-11-2013, 08:12 PM

Just fitted up an XR600 front calliper, brake ine and master cylinder. They bolted straight on. I now have front brakes that work

Pezz_gs · 04-02-2013, 01:19 AM

Some Helmet Cam footage from my GoPro from the 2013 Scrapheap Adventure Ride

Pezz_gs · 04-02-2013, 02:38 AM

A few from the weekend at the Scrapheap Adventure Ride

Last Photo - Taken by James Manson CD Media

anonny · 04-06-2013, 07:58 PM

Quote:

Originally Posted by Pezz_gs

A few from the weekend at the Scrapheap Adventure Ride

She seems really puzzled by that bike. Great stuff Pezz

Pezz_gs · 04-07-2013, 03:32 PM

That was a K100 built by Buckscreek for Scrapheap. Last year it was a sidecar, which had a little mishap on the way home, necessitating a few dyas in Hospital for the rider and passenger and a full rebuild for 2013.

Previously

2011

2012

Big favourite with the kids, my Molly at the back and my Grace beside her with the glasses and cap.

01-16-2013, 03:24 AM	#451
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	Another __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

01-20-2013, 06:23 PM	#452
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	Just found another pic of it, a bit arty __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

02-11-2013, 02:31 PM	#453
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	Time for some more work on Yajuu I need to do something serious about the front brakes on this bike Current front end is XR/XL 250 Disc brake set up. 38mm forks Honda XR-250R (84-85) Question is, what will fit on here Disc wise and calliper wise? I can fabricate an adapter bracket for a calliper if needed. Or what else runs 38mm forks, that would be suitable for a swap over? Looking at the thread below, not much on offer in 38's http://www.advrider.com/forums/showp...&postcount=198 __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

02-11-2013, 08:28 PM	#454
kellymac530 motorcycle addict Joined: Feb 2010 Location: so. cal. Oddometer: 886	Disc is gonna be a bit trial and error. 4 bolt rotor, I think newer Kawasaki KXf bikes are 4 bolt. not sure if it is the same pattern and bolt centerline though. Caliper wise, about ANYTHING newer will work better but you will need to make an offset for the bigger rotor. The master cylinder may also be an issue though, getting the right MC bore and caliper piston size ratio is critical. Rotor diameter is probably the biggest issue, that thing is a tea cup saucer, you need a dinner plate. __________________ it is easier to ask for forgiveness than permission

03-10-2013, 08:54 PM	#457
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	Well I just went out, after having the heli-coil inserted to secure Number 4 spark plug, just gave it a kick in the guts __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

02-15-2013, 07:41 PM	#456
NordieBoy Armature speller Joined: Dec 2006 Location: Kiwiland Oddometer: 6,765	Pre 2008 KLR650?

03-10-2013, 10:43 PM	#458
NordieBoy Armature speller Joined: Dec 2006 Location: Kiwiland Oddometer: 6,765	That, is the coolest sounding starter in the history of the world. Made by Nippon-Denso-Hyena?

03-11-2013, 08:12 PM	#459
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	Just fitted up an XR600 front calliper, brake ine and master cylinder. They bolted straight on. I now have front brakes that work __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

04-02-2013, 01:19 AM	#460
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	Some Helmet Cam footage from my GoPro from the 2013 Scrapheap Adventure Ride __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

04-02-2013, 02:38 AM	#461
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	A few from the weekend at the Scrapheap Adventure Ride Last Photo - Taken by James Manson CD Media __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

04-07-2013, 03:32 PM	#463
Pezz_gs ^OP Cant ride for crap Joined: Nov 2004 Location: Sydney Skunkworks Oddometer: 3,382	That was a K100 built by Buckscreek for Scrapheap. Last year it was a sidecar, which had a little mishap on the way home, necessitating a few dyas in Hospital for the rider and passenger and a full rebuild for 2013. Previously 2011 2012 Big favourite with the kids, my Molly at the back and my Grace beside her with the glasses and cap. __________________ Pezz :) Scrapheap Adventure Ride 2013 - Back 'O Bourke www.scrapheapadventureride.com.au I'm not a complete idiot -- Some parts are missing

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: .
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode