ADVrider

Go Back   ADVrider > Bikes > Old's Cool
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 04-28-2004, 05:42 PM   #1
freded OP
Wastrel
 
freded's Avatar
 
Joined: Dec 2003
Location: New Mexico
Oddometer: 174
Need your opinion on this piston

I am in the process of rebuilding a KRS. Bought an engine and it wasn't exactly what was represented so took it completely apart and am rebuilding it. This piston was either dropped or something was dropped on it. So question is it good enough to be used or should I buy a new one?
Attached Images
 
freded is offline   Reply With Quote
Old 04-28-2004, 06:07 PM   #2
Guzz
Gutless wonder
 
Guzz's Avatar
 
Joined: Feb 2002
Location: Tempe AZ, USA
Oddometer: 4,910
Just follow the basic rule in life when cooking, wrench'n, etc...

"When in doubt... Thow it out"
Unless you're a cheap bastard and then you come here to ask questions
__________________
Change must come from a barrel of a gun. -- Mao Tse Tung

When governments fear the people, there is liberty. When the people fear the government, there is tyranny -- Thomas Jefferson
Guzz is offline   Reply With Quote
Old 04-29-2004, 07:12 AM   #3
RikuY
Stuck in the Sandbox
 
RikuY's Avatar
 
Joined: Oct 2003
Location: Ft. Myers, FL
Oddometer: 736
The nick seems to be below the sealing/oil rings so you should be okay. I wouldn't use it because I am one anal bast---. The little bit of vibration or unbalance would have me regretting the damn piston as soon as I felt something and would crack it open again to rip it out.

So I would get a new one, but only because I only do the same job once!
__________________
RikuY

Beer will not solve all of your problems, but neither will milk.
RikuY is offline   Reply With Quote
Old 04-29-2004, 07:17 AM   #4
duc
Studly Adventurer
 
duc's Avatar
 
Joined: Mar 2004
Location: Downeast, Maine
Oddometer: 778
The nick in the body looks acceptanble to me, as long as you remove any sharp edges.


From my screen though, it looks like there is a nick on the upper surface of the top ring groove. If it is in fact a nick, I would reject this piston.
duc is offline   Reply With Quote
Old 04-29-2004, 10:10 AM   #5
kevbo
Rubbery-Lip Flappin' PHI
 
kevbo's Avatar
 
Joined: May 2002
Location: Albuturkey
Oddometer: 1,478
If it appears to be a ding from handling I'd use it. Make sure there is no raised area around the ding. (like the rim of a crater) Might need a little work with a riffler and some paper to take that off. Only the lower part of the skirt runs on the bore, some fancy pistons have even eliminated the area where your ding is located.

If, on the other hand, it appears to be a void from a casting, I'd be more wary.

When pistons fail, it is usually at the crown, or the ring grooves. Only if they were porly fitted, or EXTRAMLY worn will you ever see a skirt failure.
__________________
Sincerity is the most important thing. Once you learn to fake that, the rest is easy.
kevbo is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 04:40 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014