ADVrider

Go Back   ADVrider > Gear > The Garage
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 01-09-2013, 01:57 PM   #1
indr OP
.
 
Joined: Feb 2010
Location: mom's ovaries & dad's balls
Oddometer: 1,197
Cleaning Engine Sludge

1. The engine is off the bike. The crankcase is split with the transmission / drive shaft / shift drum / everything taken out of it.

2. A couple of days ago, I soaked the crankcase halves in some Murhphy's Oil Soap.

3. Now, there is slick sludge in various places on the CC halves. Inside and out. In corners and on surfaces. I'm thinking it's something like molybdenum mixed with the oil and soap. It's white/greyish.

4. It's very light in viscosity. But, there's a lot of it and it's in nook and crannies where I can' reach with a toothbrush or towel. Using a pick would take a long time.

What's the best and fastest way to dissolve this slime from the crankcases? Something that'll clean out the oil passages because I have a feeling there's a lot of the stuff in there. Are mineral spirits going to strip the engine paint?
indr is offline   Reply With Quote
Old 01-09-2013, 03:30 PM   #2
sparkymcgee
Gnarly Adventurer
 
sparkymcgee's Avatar
 
Joined: Aug 2008
Location: Southern California
Oddometer: 332
I've heard Pine Sol is the go to cleaner for engine parts. Haven't tried it, but I've seen pics and things come out gleaming.
__________________
2008 VFR800
2012 Super Ténéré
sparkymcgee is offline   Reply With Quote
Old 01-09-2013, 04:23 PM   #3
Beezer
Beastly Adventurer
 
Joined: Oct 2004
Location: Anchorage, formerly Spenard (hub of the universe)
Oddometer: 5,373
kerosene, diesel, mineral spirits, gasoline.... something petro
Beezer is offline   Reply With Quote
Old 01-09-2013, 05:37 PM   #4
RTCHIEF
Gnarly Adventurer
 
Joined: May 2003
Oddometer: 307
engine

Have it hot tanked.
RTCHIEF is offline   Reply With Quote
Old 01-09-2013, 07:33 PM   #5
CaptTeach
Gnarly Adventurer
 
Joined: Dec 2008
Location: Grenada - MS....... not the Island!!!!
Oddometer: 209
Easy Off oven cleaner in the yellow can - Place in the sun to warm up the part then spray Wait twenty minutes or so and either re-coat or rinse with water
__________________
CaptTeach

96 Heritage Softail Classic
89 XT 600
71 CB 200 Cafe Racer
70 CL 100
63 Sporty XLCH
CaptTeach is offline   Reply With Quote
Old 01-09-2013, 07:51 PM   #6
HapHazard
t00 0ld 2b n00b
 
HapHazard's Avatar
 
Joined: Dec 2009
Location: Central CT
Oddometer: 2,183
Quote:
Originally Posted by RTCHIEF View Post
Have it hot tanked.
No - that will effectively dissolve aluminum.

Try the PineSol first.
HapHazard is offline   Reply With Quote
Old 01-09-2013, 08:19 PM   #7
H96669
A proud pragmatist.
 
H96669's Avatar
 
Joined: Nov 2009
Location: Hiding off Hwy 6, B.C.
Oddometer: 4,406
Murphy oil soap, that's to clean wooden floors, not much degreasing power.

I king of object to some of the above suggestions, Caustic Lye products such as hot tanks or oven cleaners, really bad for aluminium. But I can be patient and don't have a problem picking at stuff for a long time.

Go buy some Castrol engine cleaner/degreaser at CT.
__________________
Have tools, will travel!
H96669 is offline   Reply With Quote
Old 01-09-2013, 11:44 PM   #8
Beezer
Beastly Adventurer
 
Joined: Oct 2004
Location: Anchorage, formerly Spenard (hub of the universe)
Oddometer: 5,373
if petro products don't work try paint stripper... it has methyl chloride which one of the really good cleaners we used to have in the old days, but bear in mind there are reasons it isn't used for that anymore... like it's pretty evil on your body. I brush it on and cover it with plastic sheet to keep it from evaporating

if you buy "gasket remover" in a spray can thats all it is... paint stripper

Easyoff is ok on stainless steel but be careful on aluminum... it can eat alloy
Beezer is offline   Reply With Quote
Old 01-10-2013, 04:19 AM   #9
concours
WFO for 41 years
 
concours's Avatar
 
Joined: Dec 2008
Location: Kensington, NH USA
Oddometer: 5,188
Spray wand at the car-wash, hot soapy water. Have WD-40 WITH YOU to stop the IMMEDIATE rusting on the steel bits.
__________________
Too much is just barely enough.....
concours is offline   Reply With Quote
Old 01-10-2013, 08:13 AM   #10
bomber60015
Anatomically Correct
 
bomber60015's Avatar
 
Joined: Sep 2008
Location: Chicago-ish
Oddometer: 8,642
Quote:
Originally Posted by concours View Post
Spray wand at the car-wash, hot soapy water. Have WD-40 WITH YOU to stop the IMMEDIATE rusting on the steel bits.

^ right here!

Murphy's oil soap? THAT is a truely novel application for this product . . . . .
__________________
"Here is your country. Cherish these natural wonders, cherish the natural resources, cherish the history and romance as a sacred heritage, for your children and your children's children. Do not let selfish men or greedy interests skin your country of its beauty, its riches or its romance.” T.R.
bomber60015 is offline   Reply With Quote
Old 01-10-2013, 02:13 PM   #11
redprimo
Gnarly Adventurer
 
Joined: Jul 2011
Location: central coast of California
Oddometer: 343
Dishwasher works great on chainsaw cases.
redprimo is offline   Reply With Quote
Old 01-10-2013, 02:30 PM   #12
ragtoplvr
Beastly Adventurer
 
Joined: Oct 2007
Location: S. W. Mssouri
Oddometer: 5,619
Vote for car wash, use lots of rinse. You are in BC so it is cold, keep case from freezing until you blow out well. When home blow out all passages real well. Bake in oven if at all possible at 225 for an hour minimum to dry all parts. Alternate put some place warm like near your wood stove or over a heat vent.

Rod
ragtoplvr is offline   Reply With Quote
Old 01-10-2013, 04:33 PM   #13
troidus
Beastly Adventurer
 
Joined: Sep 2010
Oddometer: 12,083
Quote:
Originally Posted by redprimo View Post
Dishwasher works great on chainsaw cases.
And on an aluminum wheel from a salvage yard.
troidus is online now   Reply With Quote
Old 01-10-2013, 04:40 PM   #14
RTCHIEF
Gnarly Adventurer
 
Joined: May 2003
Oddometer: 307
Quote:
Originally Posted by HapHazard View Post
No - that will effectively dissolve aluminum.

Try the PineSol first.
How do engine rebuilders clean oil from aluminum?
RTCHIEF is offline   Reply With Quote
Old 01-10-2013, 06:44 PM   #15
fritzcoinc
Enjoying my last V8
 
fritzcoinc's Avatar
 
Joined: Apr 2008
Location: Cypress, Tx
Oddometer: 6,481
Gunk Engine cleaner.
__________________
Regards
Fritzcoinc
96 XR650L, 96 Guzzi Sport, 07 BMW K1200GT,
86 Husky 400 XCE, 00 Husky Te 610 e, 1999 Husky TC610 SM, 2000 Cagiva GC; Google: TX7
fritzcoinc is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 03:56 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014