Cam-chain tensioner replacement - Photo Journal

Discussion in 'GS Boxers' started by Poolside, Feb 17, 2005.

  1. Poolside

    Poolside Syndicated

    Joined:
    Apr 1, 2003
    Oddometer:
    11,887
    Location:
    Silicon Beach, CA
    <BR>Last Saturday a friend and I changed the cam chain tensioner on his 2001 GS. Enjoy the photo journal.

    To begin, here is some information that will address a few common preliminary concerns.
    _____________________________


    The method of replacing the cam chain tensioner described here does not require a throttle cable readjustment.

    ***********

    The engine crankshaft does not have to be at TDC or BDC or any particular orientation.

    But, the 'tension side' of the cam chain should be tight. And the 'slack side' of the cam chain should be slack. This only means that before you start the job, rotate the crankshaft a small amount in the direction it normally turns.

    Turning the crankshaft by hand is easy to do. Put the bike on the centerstand and put the gearbox in top gear. Using your hands, rotate/bump the wheel forward until you feel some bit of engine compression, then stop.

    Good. The cam chain slack is now on the tensioner side. The chain slack is on the tensioner side when the engine is running.

    The chain slack is normally on the tensioner side. But, sometimes when the engine stops, the crankshaft rotates backward a small amount, 'slackening' the tension side. Turning the crankshaft a small amount returns the chain slack to the tensioner side.

    ***********

    The original tensioner has a spring. And when unscrewing the tensioner, when the last thread is reached, the spring will push the tensioner body up from the bore.

    The spring tension is gentle. Gentle as in about 2 pounds. About twice the spring tension of a retractable pen.

    Also, no parts can fly across the room. The tensioner body will lightly contact the bottom side of the control arm, and stop. At that point the tensioner body will be only 2/3 of the way out of the bore. That is as far as it can go under its own power.



    Getting the tensioner the rest of the way out of the bore will probably consume the greatest percentage of the total job time. It would be nice if the tensioner 'sprang' out of the bore, that would eliminate the only time consuming part of the job.

    ***********

    No tensioner parts can fall into the engine from the tensioner bore. Not even if it falls in 'just the right way'.

    At some point your hands will be working in a limited space while fiddling around trying to get the tensioner spring out from under the tensioner body. Go at this with abandon, no tensioner parts can fall into the engine from the tensioner bore.

    ***********

    Here are the factory original PREVIOUS MODEL parts, and the FIRST EDITION UPGRADE MODEL parts as of Feb '05. The first upgrade model was priced over $200

    [​IMG]



    Here are the factory ORIGINAL PARTS, and the CURRENT PARTS as of May '07. About $60 to $70.

    [​IMG]



    Start by loosening these two intake tube clamps. Do not loosen the tube clamp that is located next to the cylinder head.

    [​IMG]

    [​IMG]



    These steps are straightforward enough.

    [​IMG]



    Your throttle body o-ring may look like it has stretched. This one looks pretty good. The o-ring absorbs hydrocarbon crankcase vapors and swells. If it has, the intake tube will tear the o-ring when slid back over the throttle body.

    This phenomenon is identical to what happens to the o-rings on the fuel tank quick disconnects.

    BMW O-ring p/n 13 54 1 341 797 ___ 52mm x 2mm ___ $3.10

    [​IMG]



    Unplug the fuel injector electrical connector.

    [​IMG]



    Remove the fuel line retainer spring clip.

    [​IMG]



    Remove the two fuel line screws.

    [​IMG]



    Pop off the injector fuel line.

    [​IMG]



    Look at that, the o-ring stayed with the fuel line end cup.

    [​IMG]



    Pull out the fuel injector.

    [​IMG]



    Put the o-ring back on the injector.

    [​IMG]

    [​IMG]



    Disconnect the Throttle Position Sensor (TPS) electrical connector.

    [​IMG]

    [​IMG]



    Cut the zip-tie for the TPS cable.

    [​IMG]



    Remove the throttle body ground lead.

    [​IMG]



    Remove the two intake manifold flange screws.

    [​IMG]

    [​IMG]



    Here is a look at the end of the intake manifold 'flange'.

    [​IMG]



    You will need another special tool.

    [​IMG]



    Make a hangar out of the wire and suspend the throttle body and intake manifold out of the way.

    [​IMG]

    [​IMG]

    [​IMG]



    Without stopping to stage photos, it takes about 10 minutes to get to this point.

    [​IMG]



    17mm combination wrench works well enough to loosen the tensioner.

    [​IMG]

    [​IMG]



    Get you a big paperclip and make one of these.

    [​IMG]



    Use the small hook to grab the top, or near the top, of the spring

    [​IMG]



    First pull down on the spring, and then out from under the tensioner body.

    [​IMG]



    Here is the spring removal sequence. You may get lucky and get it the first time.

    [​IMG]



    Use the other end of the paper clip tool to retrieve the piston. Make the paperclip 'vee' large enough so that it is a force fit and will grasp the piston from the inside.

    [​IMG]



    Old parts going to the archive.

    [​IMG]



    Now it is time to install the new tensioner. Start by dropping the piston into the cylinder bore. (There is no picture of this step.)

    The large piston can be dropped into the bore . . . plunk. The old piston did not fall into the engine, and neither will the new one. Just drop it in.

    The new components fit together like this. It is easier to drop the piston into the cylinder bore that to try to install them while mated.

    [​IMG]



    Slam dunk. Remember, the top of the tensioner body must go up and behind the suspension arm before it can be guided into the bore.

    [​IMG]



    These casting marks are for component alignment.

    [​IMG]



    Rotate the fuel injector body out of the way, and snap on the retaining clip.

    [​IMG]



    The fuel injector retaining clip must slide on smoothly with a nice 'detent click' when fully seated. If the retaining clip does not slide on smoothly, the problem is the injector is not pushed far enough into the fuel cap.

    [​IMG]



    Rotate the injector body so that it is in front of the retaining clip.

    [​IMG]



    Plug in the electrical connector. When oriented correctly, the electrical connector blocks the injector retaining clip.

    [​IMG]

    [​IMG]



    Job complete. A-a-a-h-h - h - h. The first start up was nearly silent.

    [​IMG]



    Thanks for the props everyone. Happy wrenching.

    - Jim<BR><BR>
    #1
  2. philschl

    philschl Been here awhile

    Joined:
    Apr 13, 2004
    Oddometer:
    222
    Location:
    Sydney
    Nice one, Jim!

    I need to take off my right TB for rebushing the butterfly shaft, so thanks for the picturesque step-by-step instruction!

    Phil
    #2
  3. configurationspace

    configurationspace delooper

    Joined:
    Jan 26, 2003
    Oddometer:
    10,345
    Location:
    Kanadia
    Wow, Poolside. That's beautiful. I might just change my cam chain tensioners so I can use all this wonderful information.
    #3
  4. johnjen

    johnjen I've Been Resigned

    Joined:
    Nov 28, 2001
    Oddometer:
    16,693
    Location:
    Seattle
    Jim this is really great. My only concern is that bike looks way to clean. How can such a clean machine need new tensioners? :D

    JJ
    #4
  5. Andrew

    Andrew Optimus Primer Super Moderator

    Joined:
    Sep 25, 2001
    Oddometer:
    17,028
    Location:
    Eastbania
    #5
  6. HarveyMushman

    HarveyMushman Tire Squarerer

    Joined:
    Jun 21, 2002
    Oddometer:
    16,986
    Location:
    Virginia, USA
    You da man, Jim. :thumb
    #6
  7. HarveyMushman

    HarveyMushman Tire Squarerer

    Joined:
    Jun 21, 2002
    Oddometer:
    16,986
    Location:
    Virginia, USA
    You still da man, Jim, but where's the rest? :D
    #7
  8. kbasa

    kbasa Roubaix! Super Moderator

    Joined:
    May 28, 2002
    Oddometer:
    72,497
    Location:
    Marin County, California
    This is wonderful. Really.
    #8
  9. rideLD

    rideLD The further the better!

    Joined:
    Jul 15, 2004
    Oddometer:
    5,412
    Location:
    Omaha, Nebraska
    Me god, that thing is filthy. Is that old varnished gas in the TB? Whats with all that carbon in the intake? Is that comon with boxers? I have rebuilt top ends on countless japanese bikes and never seen that much crud, even at 100K. :dunno

    BTW, thanks for doing this. It will be a great reference for all.:thumb
    #9
  10. Arch

    Arch Incurable Gearhead

    Joined:
    Dec 30, 2001
    Oddometer:
    11,705
    Location:
    Katy, TX
    Yep! Rockin' how-to, Jim! Duly bookmarked. :thumb
    #10
  11. eap

    eap El Adventurero Solitario

    Joined:
    Nov 1, 2001
    Oddometer:
    3,341
    Location:
    Maryland, Least Coast USA
    great work!:thumb
    #11
  12. configurationspace

    configurationspace delooper

    Joined:
    Jan 26, 2003
    Oddometer:
    10,345
    Location:
    Kanadia
    Yay! Poolside! Yay!
    #12
  13. Rad

    Rad Done riding

    Joined:
    Sep 24, 2001
    Oddometer:
    12,176
    Somethun tells me this might just end up in that hall with the other smarty stuff :nod

    That would have nut'n to do with the fact that I have an 01 GS with a tick'n on the left side :lol3
    #13
  14. johnjen

    johnjen I've Been Resigned

    Joined:
    Nov 28, 2001
    Oddometer:
    16,693
    Location:
    Seattle
    we're work'n on fixing up the Hall of Wisdom so we can get reports in there faster...

    and this is a choice morsel indeed.

    JJ
    #14
  15. Bill 310

    Bill 310 Poser Emeritus

    Joined:
    Dec 4, 2002
    Oddometer:
    3,453
    Location:
    Hopefully Upright
    #15
  16. eap

    eap El Adventurero Solitario

    Joined:
    Nov 1, 2001
    Oddometer:
    3,341
    Location:
    Maryland, Least Coast USA
    BTW - where is the Hall of Wisdome nowadays. I've wanted to pull up the OVAD for a buddy but don't see it anywhere...
    #16
  17. johnjen

    johnjen I've Been Resigned

    Joined:
    Nov 28, 2001
    Oddometer:
    16,693
    Location:
    Seattle
    That's a good question...

    Oh Baldy, paging Mr. Baldy...

    JJ
    #17
  18. Team Dennis

    Team Dennis Certified Troublemaker

    Joined:
    Aug 28, 2002
    Oddometer:
    4,537
    Location:
    Tornado alley
    Moved to the bottom of the page next to the donate button.
    #18
  19. eap

    eap El Adventurero Solitario

    Joined:
    Nov 1, 2001
    Oddometer:
    3,341
    Location:
    Maryland, Least Coast USA
    Oh there it is:confused .Down at the frign bottom of the page, GDMHK always moving things around :huh thanks,
    #19
  20. configurationspace

    configurationspace delooper

    Joined:
    Jan 26, 2003
    Oddometer:
    10,345
    Location:
    Kanadia
    Woohoo! Poolside! :smile6
    #20