Help- R1150GS front brake- no brake light

Discussion in 'GS Boxers' started by rocketman1, Nov 30, 2012.

  1. rocketman1

    rocketman1 rocketman1

    Joined:
    Aug 6, 2010
    Oddometer:
    127
    Location:
    NZ
    Hi I have a 2003 R1150GS, first little problem in 3 years. The front brake will not not make the rear brake light operate.
    The rear brake brightens the brake light no problem. All other electrics works fine and bike runs well.
    I have traced the wiring back as far as I can from the front brake and cleaned up the first connection.
    Has anybody else had this problem? I would like to know where to start .
    #1
  2. Mr. Canoehead

    Mr. Canoehead Taste Gunnels!

    Joined:
    Apr 16, 2007
    Oddometer:
    2,198
    Location:
    Calgary, Too far to the mountains and too cold
    Do you have ABS? The brake lights work opposite for ABS/Non-ABS bikes.
    #2
  3. Zoef zoef

    Zoef zoef Been here awhile

    Joined:
    Apr 19, 2009
    Oddometer:
    545
    Location:
    Finn√ły Island, near Stavanger, Norway
    Sir,

    There is a microswitch near the base of the brake handle. You should also hear that click when you move the handle. When you have the servo ABS, the switch is "normally closed" which is the opposite of normal brake light switches, which are "normally open". If I not mistaken the switch has its connector under the front of the fuel tank.
    #3
  4. CNRED

    CNRED It'll be OK

    Joined:
    Feb 17, 2008
    Oddometer:
    631
    Location:
    Scottsdale, AZ
    Ran into this problem with a 1999 R1100gs, it was the brake light switch. I'm not sure if the 1100 and the 1150 share the same front master cylinder or not, but the brake light switch on the 1100 sits just below and attached to the master cylinder. Over the years, brake fluil had leaked out of the master cylinder bowl and onto the switch. It ate away at the switch until one day, no brake light. Replaced the switch light worked again.
    #4
  5. Twilight Error

    Twilight Error Going nowhere slowly

    Joined:
    May 18, 2002
    Oddometer:
    22,867
    Location:
    The Submarine Mines
    Note: Most 1100 and 1150 models are equipped with ABS from the factory. Versions of ABS vary, but they all route the brake lamp switches through the ABS computer. If you remove the ABS unit, you've also got to rewire the brake switches to activate the lights. BMW uses NC switches.

    EDIT: replaced ALL with Most. It took some digging, but I did find indications that I was wrong. The parts fiche shows two FD PNs, one for ABS and one without. Based on that, I've got to assume a non-ABS version was available at some point.
    #5
  6. Steptoe

    Steptoe steptoe

    Joined:
    Feb 21, 2004
    Oddometer:
    2,948
    Location:
    london, England
    This information is completely and absolutely wrong.
    The poster is assuming all abs equipped bikes from 1994 up until 2005 are the same. They aren't.
    The posters example is relevent ONLY to 1150 bikes equipped with ABS AND SERVO brakes from 2003.
    #6
  7. Gezerbike

    Gezerbike Hey Rocky...........

    Joined:
    Jul 8, 2002
    Oddometer:
    3,825
    Location:
    Everybody knows this is nowhere......
    And there was a model called the " Sport " that only came in yellow and it did not haave ABS. And the 1150 used different switchgear than the 1100.
    #7
  8. Mr. Canoehead

    Mr. Canoehead Taste Gunnels!

    Joined:
    Apr 16, 2007
    Oddometer:
    2,198
    Location:
    Calgary, Too far to the mountains and too cold
    Yes, I have a friend with a 2004 GSA and no ABS from the factory. I think that if you had a bad switch on a servo bike, you would also have no brakes since (I believe) that the switch is actually what activates the servo.

    Since the OP has a 2003, he may or may not have servos but if he has ABS he will have servo brakes..
    #8
  9. sidetrack one

    sidetrack one Chief Tiddler

    Joined:
    Jul 2, 2006
    Oddometer:
    7,335
    Location:
    hole shaven area
    What a crock of shit!!
    The Battle Bike dont got no stinkin' ABS!! and I believe its an 1150!:evil

    [​IMG]
    #9
  10. dfwscotty

    dfwscotty Long timer

    Joined:
    Apr 9, 2006
    Oddometer:
    3,704
    Location:
    Denton, TX
    Stick your ear next to the front brake handle. Squeeze the handle and see if you hear it clicking. My '99 had issues like that. Maybe it would work, maybe it wouldn't. If you don't hear it click then the plunger switch is not fully activating the light.

    I was preparing to replace the switch and started to tear into it to see if I could fix it or replace something. I found the microswitch. I sprayed some contact cleaner and soaked it real well. Exercised it well, stuck it back in the bike and haven't had an issue in over a year.
    #10
  11. rocketman1

    rocketman1 rocketman1

    Joined:
    Aug 6, 2010
    Oddometer:
    127
    Location:
    NZ
    Thanks for your help guys.
    I separated the wired connection juntion which is fixed to the frame just below the handle bars on the right hand side.
    I checked the resistance to the circuit with my ohm multimeter, and the there was a high resistance ie. 0.50 / 0.60 ohms when operating the handbrake, .should be Zero
    I removed the microswitch and wiring from below the front brake master cylinder, then checked the open circuit on the bike with a couple of wires and sure enough the brake light works.
    Ichecked the internet and saw that this replacement part was about $60.00. I thought , thats 3 tanks of gas!!
    I then decided to pull the wee microswitch apart and clean it up. So I put on my magnification glasses 4x, and if you look very closely you will see that this switch has a little stainless hinged lever, with a very small screw driver lever this clip off, then very carefully use the same jewellers screwdriver to separate the two parts of the switch.
    Wow inside is a tiny little spring and a set of contacts. All i did was to get some fine emery paper and sand the contacts which are about half the size of a pinhead, I then squirted it all with CRC cleaner and carefully dried it all.
    At this stage before I checked it with my multimeter, sure enough the resistance was Zero.
    Fitted it back on the bike, cable tied it all back together and it works perfectly. Zero cost.
    This took about two hours to complete, fiddley, but satisfying to fix.
    Thanks for your help again.

    Cheers
    #11