Rate your Harbor Freight Tool Experiences!

Discussion in 'The Garage' started by JimVonBaden, Dec 28, 2011.

  1. JimVonBaden

    JimVonBaden "Cool" Aid!

    Joined:
    Feb 11, 2005
    Oddometer:
    56,193
    Location:
    Alexandria, VA
    Please rate your experience with specific tools/items purchased and used from Harbor Freight. Note the link to the item, if you got it on sale, a photo if you can, and your DIRECT experience with that item.

    Anyone who is interested in buying inexpensive tools and items from HF can use this thread to see if what they are interested in has a chance of being worth the price!

    This thread is NOT about wheather or not you should buy things from China, or anywhere else. It IS about helping people decide the good values from the bad at Harbor Freight. Please do not waste our time with rants about HF and Chinese crap.

    I'll start out with examples!

    Three years of hard labor: http://www.harborfreight.com/1000-lb-capacity-motorcycle-lift-68892.html
    [​IMG]
    Major Pass, and only $289 for the air/manual lift version on sale!


    http://www.harborfreight.com/motorcycle-wheel-chock-96349.html
    Similar three years:
    [​IMG]
    Pass. It is great for getting a bike on the lift alone, and holding it while tieing it down!


    http://www.harborfreight.com/1500-watt-dual-temperature-heat-gun-572-1112-96289.html
    [​IMG]
    Pass, lasted three years, for $9.99 on sale.


    http://www.harborfreight.com/9-piece-14-and-38-drive-star-bit-set-67914.html
    [​IMG]
    Pass, excessive use, and the Allen sockets, with no failures, and lots of abuse.


    http://www.harborfreight.com/catalog/product/view/id/1360/category/434/
    [​IMG]
    Got on super sale for $12.99. MAJOR PASS! Works great, especially for the price. Now if only I could weld worth a damn.


    http://www.harborfreight.com/automo...tands/3-ton-heavy-duty-jack-stands-38846.html
    [​IMG]
    Pass, but beware of using them on assphault as they will sink in.


    http://www.harborfreight.com/catalog/product/view/id/302/category/433/
    [​IMG]
    Pass, strong and cheap at $39 on sale.


    http://www.harborfreight.com/power-tools/polishers/7-inch-variable-speed-polisher-sander-92623.html
    [​IMG]
    PASS! This thing is great! Holds the HF 7" rubbing and buffing pads (also great!) and the other accessories.


    http://www.harborfreight.com/power-tools/sanders/5-inch-random-orbital-palm-sander-93431.html
    [​IMG]
    Pass, but the dust collector is worthless!

    http://www.harborfreight.com/hand-tools/precision-hand-tools/4-piece-pick-and-hook-set-66836.html
    [​IMG]
    FAIL Cheap and bend easily!

    http://www.harborfreight.com/hand-tools/screwdrivers/6-piece-screwdriver-set-92193.html
    [​IMG]
    FAIL!!!

    I have used LOTS of HF hand tools, and most are OK, the screwdrivers are generally crap, unless you use ones with replacable tips, but otherwise they do NOT do well.

    Jim :brow

    PS Yes, I know Poolside (Jim) has a similar thread, but this is about pass or fail on specific items, so different.
    #1
  2. Skippii

    Skippii Milkshakes, my lad.

    Joined:
    May 11, 2008
    Oddometer:
    6,530
    Location:
    Richmond, Va
    I also have the blue flame version. I paid $39. Works fantastically, and has enabled me to weld much better than before I had an auto-darkening helmet. Mostly just because now I can start my welds in the correct place. Anyway, I'm not blind, so I'll say PASS.


    I use it with:

    http://www.harborfreight.com/120-amp-arc-welder-98870.html
    (I can't post the images from work)
    I paid $69 for it refurbished. I've probably burnt 50 pounds of rod with it. Never had a problem with it, ever. I've used it with 1/16, 3/32, and 1/8 rod on both 120 and 240 volts (It likes 240V MUCH better). PASS.


    http://www.harborfreight.com/80-piece-rotary-tool-kit-97626.html
    (actually, I can post the images...but they come out rather large:
    [​IMG]

    FAIL. Where do I begin to describe this piece of shit? The power supply is basically a tiny bit larger than your average cell phone charger. It buzzes and spins, but when you touch a spinning cut-off wheel to a peice of PLASTIC (forget about metal) it instantly stalls and wimpers. It has no power. If you intent to use this to drill, grind, cut, or even scratch something, forget it. My ex had vibrators ten times more powerful than this crap.

    I think I have this, but mine only came with 5 bits...
    http://www.harborfreight.com/8-in-1-reversible-ratchet-screwdriver-31555.html
    [​IMG]
    FAIL. it doesn't ratchet well...it just works like some kind of torque wrench, where after about 1 foot pound of force, it disengages and spins. If you switch it to the "locked" position where it should work like a normal screwdriver, it spins in both directions. Also, if you are lucky enough to make the screwdriver actually work, the bits break. This might be the first time I've ever bought a screwdriver that didn't work.


    http://www.harborfreight.com/7-function-digital-multimeter-90899.html
    [​IMG]

    7 Function Digital Multimeter- I think I paid $3.99. PASS. It's worth the price just for the transistor test, where it shows the Hfe of any NPN or PNP tranisitor you plug in, as long as you get the trannies in *just* right so it can read them. The resistance (ohm meter) function works well, but be aware that the signal voltage and current it uses is surprisingly high (over 3 volts), which is strong enough to damage some ultra-sensitive component and will light up LEDs. The probes are crap and will fall off the wires if your not careful, so solder them on or something.
    #2
  3. facetjoint

    facetjoint TONKA

    Joined:
    Jan 7, 2010
    Oddometer:
    5,607
    Location:
    Phx. AZ. The land of shake and bake
    I have the heat gun, ' GOOD" the metric hex head sockets "REAL GOOD", and I used to have the orange o-ring picks "JUNK as you indicated.

    Probably my best one is an old HFT 5 gallon pan cake compressor. I'd guess 15 or so years old. It won't die. I've used the heck out of it. It won't run any air tools. But it is great for tires and to blow the fecal matter off tons of anything I tear apart. Which is almost daily.
    #3
  4. FatChance

    FatChance Road Captain

    Joined:
    Jun 12, 2003
    Oddometer:
    10,784
    Location:
    Durango, Colorado, USA
    I have the 1000lb motorcycle lift as pictured, Excellent!

    Also, the wheel chock on the lift as pictured, Excellent!

    Also, the heat gun as pictured, Very Good!

    Also, the motorcycle tire changer. Good. (With some aftermarket additions, Excellent!)

    [​IMG]
    #4
  5. Dave in Wi

    Dave in Wi Long timer

    Joined:
    Feb 25, 2007
    Oddometer:
    2,063
    Location:
    Madison WI (40 Square Miles Surrounded By Reality)
    I have used both the Cen Tech digital calipers and micrometers. They were cheap, dead nuts accurate (checked them against my feeler gauges), readings are repeatable, and my eyes LOVE the fact that they are digital. And you can get readings in metric or inches.[​IMG]

    I also recently bought a single 6 point socketat HF to loosen the clutch nut on my atv (24 mm or something like that). 99 cents on sale. How can they do that? It worked fine and now I have it whenever I need it.
    #5
  6. Speedo66

    Speedo66 Transient

    Joined:
    Jan 14, 2010
    Oddometer:
    6,970
    Location:
    Cin City, OH
    Had one of their 4'x8' folding trailers with the 12" wheels. Piece of 4x8 plywood and you were in business.

    For less than $300 delivered at the time, it did what it was supposed to do, carried two bikes with no problem.

    Used it millions of times to haul homeowner stuff, etc.

    Not pretty, not particularly strong, but it never failed. Paint sucked, had to watch for rust, and wire brush and touch it up occasionally.

    But when I sold it, I actually got more than I paid for it, so it literally owed me nothing.

    This one http://www.harborfreight.com/1195-l...tility-trailer-with-12-inch-wheels-90154.html

    PASS

    Bought a set of their circlip pliers, you know the ones with the 2 tiny points that fit into the holes. When the tips weren't bending, the part of the pliers that held them wouldn't hold them, kept letting them move out of place.

    These things http://www.harborfreight.com/catalogsearch/result?keyword=circlip+pliers

    FAIL
    #6
  7. RonkoRider

    RonkoRider Wrong Island, NY

    Joined:
    Oct 21, 2006
    Oddometer:
    1,603
    Location:
    Middle of Suburban Hell- Long Island, NY
    :lurk
    #7
  8. hugemoth

    hugemoth Long timer

    Joined:
    Sep 6, 2007
    Oddometer:
    3,093
    Location:
    In the TARDIS
    I have lots of HF tools. 3 trailers, 110V flux welder, auto darkening helmet, bench top drill press, air compressor (oil type), 4.5" angle grinder, vise, combination wrenches, ratchet wrenches, 800/900 watt 2 stroke generator, battery charger, battery disconnect switch, soldering gun, soldering iron, hammer drill, 3/8" drill, orbital sander, car polisher, saber saw, vacuum pump, paint sprayer, automotive code reader, multimeters, propane bottle refiller, Vice Grip type pliers, gear pullers, tire plugs, tire patch kits, motorcycle tie down straps, bungie cords, tarps, safety goggles, hearing protection ear muffs, even a zippo cig lighter copy and hand warmer. Lots of stuff I can't think of at the moment. All excellent.

    I did have a reciprocating saw that blew the gears after about 2 hours use, a 1000 watt generator that developed a bad valve seal after 2 years (replaced under extended warranty but could have easily fixed it myself), a butane torch that fell apart.
    #8
  9. Ratski

    Ratski Been here awhile

    Joined:
    Dec 21, 2009
    Oddometer:
    769
    Location:
    Eastern WI
    I have the 12 ton shop press

    [​IMG]

    And it works great!! Pass!

    Had the Auto Wire Strippers

    [​IMG]

    You had to turn the tension up so far to make them work right that they last about 15 tries, the something went SNAP inside and they ceased to function. FAIL!
    #9
  10. CA Stu

    CA Stu Steer with your face! Super Moderator

    Joined:
    Aug 27, 2004
    Oddometer:
    48,322
    Location:
    Riverside, CA

    Me too, I added a wheel clamp I bought off ebay and it has been a super-handy lift.
    Unfortunately, the bottle jack in mine leaked out some fluid and I had to top her up...

    The black drill bits they sell are junk, pure and simple. FAIL Spend the extra for good drill bits.
    #10
  11. JimVonBaden

    JimVonBaden "Cool" Aid!

    Joined:
    Feb 11, 2005
    Oddometer:
    56,193
    Location:
    Alexandria, VA
    Way to go guys! This is the kind of information I was hoping to gain.

    I too have the 110V Flux welder. I suck at it, but I suspect it is more me than the welder! I did find that the HF welding wire was not nearly as good as the Lincoln wire at Lowes.

    I also have the Motorycle Tire changer, or did. It is no longer available, so I left it out. It was worth every dime of the $70 I paid for it with over 250 sets of tires changed.:clap

    Thanks, and keep it coming!:deal

    Jim :brow
    #11
  12. P B G

    P B G Long timer

    Joined:
    Mar 7, 2008
    Oddometer:
    10,001
    Location:
    Greater Chicago
    [​IMG]
    Pass!

    [​IMG]

    Pass

    [​IMG]

    PASS but slightly lower pass than the other two, the metal shelves and door feel a bit thin/tinny. Has functioned well, but the drawers on the other units are pretty impressive, the door on this feels a bit thin, but that's because its a large flat door, needs reinforcement trusses to not vibrate/make noise when opened/closed. Overall good.

    [​IMG]

    PASS - But the abrasives and accessories are subpar, get goot abrasives and cutters, patterns will not match very well however, so I would avoid this particular tool if you require the toothed cutter attachments, or if you do, just clamp the blade down hard. Dremel makes a good toothed cutter but their electric version is 100+.


    [​IMG]
    I have the cordless version of same and enjoy it so far I use this with a cast blade for a portable cast cutter.


    [​IMG]
    Pass - Not greatest drills ever, but a complete set. If you do a lot of (insert specific task) buy a good bit for that task, but having all the drills = yes.

    [​IMG]

    Low Pass - Not great stepped drills, but for around the garage they have come in handy many times.

    [​IMG]
    Medium Fail - Usable on occasion, but they don't cut very well, I usually utilize my regular wood drill bits over these, but haven't thrown them away.

    [​IMG]
    Pass - Have these in standard and metric, Mine have worked OK, not overly stressed because I use a set of snap on socket drives for anything critical, but once things are loose these work great for spinning things in/out. And general around the shop usage. Have not broken them or worn them out. Bondhus feel way better, solid metal core in rubberized handle, but these are ~5 bucks a set, less when you get the right flyer.

    [​IMG]
    Fail - Readings seemed wonky, brother left in back window of car and it seemed to "cook" to death in the sun. Can't handle the heat....


    20 ton shop press - Pass with modifications (glue rubber in to shim the press a bit)

    Digital Calipers Pass

    Welding Auto-darkening - Pass

    [​IMG]
    Fail/Pass - Bit softer than ideal, if you want to transfer to wood, plastic, or soft metal = OK.
    #12
  13. pvangel

    pvangel Team AARP

    Joined:
    Sep 29, 2005
    Oddometer:
    2,652
    Location:
    South Salem, NY
    I have the air/hyd lift as well, over two years now and has worked perfectly. I never use the air part of the lift because my compressor is small and it's really easy to just pump it by foot. I love it!

    [​IMG]
    #13
  14. MotorradMike

    MotorradMike MIL-TFD-41

    Joined:
    Aug 17, 2008
    Oddometer:
    1,026
    Location:
    Mallorytown Ontario
    Good thread!

    I'm not going to say Pass or Fail but I'm going to weigh in.
    First, we don't have HF in Canada but we do have Princess Auto which is very similar.
    These calipers sucked me in because they were $10 and just beyond the end of sale date but the staff let me have them at the sale price anyway.
    I got them for measuring stuff under the car during the Winter.
    Hard to complain about 10$ digital calipers but they have no depth gauge and a resolution of .01" which I really don't like.
    Just a warning to those who may also get sucked in.
    To coin a new phrase, "You get what you pay for".
    [​IMG]
    [​IMG]
    #14
  15. P B G

    P B G Long timer

    Joined:
    Mar 7, 2008
    Oddometer:
    10,001
    Location:
    Greater Chicago
    HF has this

    http://www.harborfreight.com/6-inch-digital-caliper-47257.html

    For ~15-30 depending on the sale in process, this is a very good digital caliper for most uses, if you need more accuracy you better have an expensive lathe.
    #15
  16. Longboardr

    Longboardr Been here awhile

    Joined:
    Aug 11, 2010
    Oddometer:
    143
    Location:
    south central PA
    Motorcycle tire bead breaker
    Had to add a long piece of tubing to the handle for more leverage and I'll clamp it to the table next time I use it. Broke the bead as advertised. Hard to beat for $20

    Attached Files:

    #16
  17. JimVonBaden

    JimVonBaden "Cool" Aid!

    Joined:
    Feb 11, 2005
    Oddometer:
    56,193
    Location:
    Alexandria, VA
    Nice! I was looking at this one myself. I might pick one up tomorrow!

    Jim :brow
    #17
  18. ksrider

    ksrider n00b

    Joined:
    Jun 18, 2011
    Oddometer:
    9
    Big Pass! I got this wheel balancer for about $50. Works very well.

    Attached Files:

    #18
  19. Superdave Osborne

    Superdave Osborne Runs with scissors

    Joined:
    Mar 8, 2010
    Oddometer:
    47
    Location:
    Spokane, WA
    Was just wondering about that one.
    #19
  20. svejkovat

    svejkovat Been here awhile

    Joined:
    Jun 23, 2009
    Oddometer:
    856
    Hmm,
    A 3/8 sliding T handle socket wrench. Unusual design. Never seen one before like it. Made in Taiwan. Love it. Versatile and nicely made. Didn't see it listed. Guess it's no longer avail?


    [​IMG]
    Pass. Who knows how consistent is the quality of these odds/ends assortments from ship to ship, but the bin I got was excellent. I find these things pretty useful.

    [​IMG]

    Fail. For basic electronics they're fine and a great bargain. But for motor vehicle use here at ADV I discovered that these to not bear up well to gasoline or solvents. The 3M stuff that I've used is excellent by comparison. This stuff almost melts.

    [​IMG]

    Fail. Did not get this assortment, but an assortment of the that serrated edge style. The metal is of such poor alloy that the 'teeth' are easily squashed into uselessness.

    [​IMG]

    Pass. But only because they are 1/8 the price of the better ones and sometimes you just need any step drill in pinch and these at least do the job. But I really prefer the single flute type...
    [​IMG]
    ... for ease of use and accuracy.

    [​IMG]

    Pass. I've got pretty expensive mitutoyo. This one was on sale for nine dollars so I got it for roughhousing. Turns out to be decently built and accurate enough for 98 percent of my needs. The mitutoyo hardly leaves it's case. Like many of this quality level of tools, I like to open half a dozen boxes and look closely at the mating parts, screw threads, mating lines of cases, etc. It's usually easy to find the 'pick of the litter' this way since there are often very slight irregularities.

    [​IMG]
    Pass. Nine dollars came to seven something with a 20percent coupon. Has worked beautifully for my needs. Again, open a few boxes and pick the best one. Check the alignment of the pin to the anvil. Turn it and check the runout. Not talking thousanths here. But some I checked were really out of whack. Had to turn down the diameter of the pin just a bit to fit a 415 chain.

    [​IMG]

    Pass. Sometimes you just grab this instinctively and wonder why you never had one before. One of those tools I never bought, because it seemed an extravagance. But at this price.... it was a nice discovery.

    [​IMG]

    Fail. But it's personal. They look well made enough but I just couldn't get comfortable with the locking mechanism. A tiny ball ramps back in the head and digs/locks into the band. Problem is that with traditional nylon style mechanisms the ratchet is pretty precise and easy to gauge the clamping pressure. With these, once tightened, they back off a bit to set the little ball bearing. You need to over clamp, very carefully, to compensate. And then if you get it wrong, you can't readjust since the ball has imprinted the strap and now refuses to tighten just a "little more". Frustrating. I returned them.

    [​IMG]

    Big Pass. I love these. I only wish they had a set twice the size in closer increments. Hold up well if used with care. Love them for clean holes in gaskets and for making plugs and washers out of a variety of materials. Easy to resharpen.

    [​IMG]

    Pass. Handy and in lots of sizes. Easy to machine to other useful sizes. Thick enough for crush washer use.

    [​IMG]
    Pass. With a decent selection of brass and copper tubing you can do some nice precision plumbing. This swaging tool was on sale for four bucks so I got a couple of them. One I cut into three pieces for shallow depth work.

    Lots of other odds and ends. But this is all I thought of off hand.
    #20