Separate names with a comma.
Discussion in 'Parts' started by ag_streak, Jan 26, 2010.
Are those the stockers or after market?
I have some stock parts that came off of a 2008 Yamaha WR250R. Free Pick up only..... Near Long Beach
All stock emission parts plus tank. None of this stuff had more than 500 miles on it.
I believe they are stock. Stamped HM MN5 E1 HONDA
Very good, thought they might be an aftermarket, I have a 97 with very low miles, if they were aftermarket I would have given them a try. Been awhile, hope all is good.
Wiring Hodgepodge, that's what I've got here. All packed up in a USPS small flat rate box ready to ship for $8...
Please take it all as it's already boxed up and ready to go, would be a hassle to break it all open.
couple of SAE connectors-to-alligator clips cables, one is fused
couple of SAE connectors-to-heated clothing connectors, both fused
three BMW-to-SAE connector cables
SAE-to-battery terminal cable, fused
couple of SAE connector pigtail cables for your own DIY project(s)
Electrical DIBS Dibs retracted
Dibs. I'll PM you in a minute.
If mikeysduck can part with the low profile (right angle) AMPS male plug to SAE connector, it would be of great use to me.
Handlebar Switch Mounting Hodgepodge, yes another hodgepodge. Again all boxed up in a USPS flat rate small box ready to ship for $8.
Various thingies to mount switches for whatever to your handlebars. Have at it.
Please take it all as it's already boxed up ready to go and would be a hassle to break it all open.
Gas tank mounting assembly, twist & lock with key. Not sure what else to call this. It's intended purpose is to mount one half to the gas tank ring and the other half to a tank bag or whatever. Mate the two sides by twisting together and locking for a floating tank bag over your gas tank. I was planning on using it to mount something to a sidecar setup. It doesn't have to be used for mounting a gas tank-to-tank bag. Use your imagination.
Looks like it's made of ABS or similar and 5-1/2" diameter.
All packed up ready to go in a USPS small flat rate box, shipping for $8.
In for the switch thingys.
I type too slow and my fingers are too fat.
Dibs on the gas tank ring.
WR250R Flatland Radiator Guard - Free to good home (Just pay for Shipping or Local Pickup)
Bend in the guard was made for clearance when running my 4.7 Gallon IMS fuel tank.
I'll take that off your hands if it's still available. :)
It is yours
Clover textile riding pants. 32 inch waist, they are Italian, so it is closer to a 31. If I could drop 5 or 10 pounds, I’d wear them.
They are a bit dusty and dirty. I have not worn them in 10 years.
Similar to this pic but the ones I have are an older model. I’ll take a look around for the insulated liner but I don’t think I have it.
Call dibs, then send me a PM. Taker pays shipping, I’ll ship the most economical way.
Moto, you can do it ! Keep them. On the other hand i’d have to go in a time machine an go back a few decades.
Dibs on those pants if you don't change your mind about dieting, Yinzer.
QuadGear UTV Roll Cage hand holds. I used these, with some foam pipe insulation inside of them, attached to the grab rails of the GS to give something for my wife to really hold on to while riding. They can be used for much more if you use your imagination. ATV/UTV roll cages, side case carrying handles, etc.
They're a perfect fit in a USPS Small Flat Rate box for $8 shipping (lower 48 only please) ...