1984 R80 G/S WB1034803E6362926 1) 05/6/86 Purchased New from Psycle Therapy, Columbus Ohio by B Grimes (Urbana Ohio). 2) 4/16/98 Purchase from Competition Accessories (Springfield Ohio) with 57,4557 miles, C. Roelling (Miamsburd, OH), for $1,500 3) Gunner65 purchased and only had it for 3hours 4) Lexington owner purchased it from inmate Gunner65 5) 09/11/2008 One Less Harley (KY) with 95,000 miles from a guy from Lexington KY, who didn't own it very long. According to Gunner65 the bike has been to Alaska at least twice. Cosmetically challenged when I purchased it, mechanically very good and well maintained. Very clean oil oil pan w/ no sludge. Nice original example. Bike now has a R100GS front end w/ HH Race Tech Inserts, 4 pot Brembo, Taller 5th gear, top end rebuilt, Enduralast, repainted blue. Links to miscellaneous post- 1) Death Wobble 2) Connecting Volt guage to G/S 3) Bosch Starter Repair, Bendix Replacement 4) Motor won't turn over, this is unusual-Starter related 5) Clutch Balance marks 6) Head job, rings, rod bearings-good post 7) Painting HPN tank (polyethlene)??, why not? 8) 320mm brake upgrade 9) Tanks to fit an R80 G/S 10) R80 G/S upside down brake arm conversion 11) Fix for Acerbis (OMG) petcock, left and right ones now point the right way 12) Transmission rebuild mislabeled 17.5 degree primary gear 13) BMW Performance School 14) Trail Tech MR16 HID lights are crap, 2 lights 2 failures!!! 15) 4 Pot Brembo Caliper conversion for GS 16) Damned neutral switch again!!! 17) Airbox Engine Breather Modification 18) Happy Trails Top Mounting Bracket Fix 19) Page 3, Post #45 ring gear bearing replacement 20) Page 5, post #65 R100GS front end 21) Page 1, post #10 Flywheel Issues, no rivets 22) Float bowl leashed Sololobo's article 23) HH Race Tech R100GS fork inserts. 24) Final Drive Breather Hose 26) Carb jetting Changes and notes 27) Hanging Idle discussion 28)Larger Foot Pegs from KTM 29) R80G/S to 2012 MOA Rally via the TAT 30) Float Bowl Leashes 31) DRZ forks, Unholy Union w/ Prutser's top clamp 32) Frame Straightening and Bracing 33) Failed Heads report at 25,000 miles Thanks CARL aka Flying T Pot 34) Side stand lengthening 35) Solo seat rack mod and rack mounts 36) Nippondenso Starter install 37) Bean Can repair with new HES 38) Timing Chain Replacement (page 20, post 366) So here's the old gal as purchased, notice the big honking headlights and angle irons for brackets. ...and here it is now. (Update bike current pict) One of this first things I did was drop the oil pan to check for gunk in the engine and check the oil pickup. I've heard these can loosen up. All was well inside along with changing all the fluids, that included the brake fluid. (Oil pan w/oil) Next on the project was to pull the tranny and lube the splines, plus since the rear frame was off why not powder coat it??? (spline Lube PIct) Then a custom muffler guard for the Sito Muffler out of plain metal rods. Look here for link http://www.advrider.com/forums/showthread.php?t=387232 (sito custom Muffler Guard) Then some eyebrows for the large PIIA's as I was getting a glare from the top edge. Then reinforcing stock racks for the Happy trails panniers. Gussets added. (saddle BAg gussets) And a rear bar, stood up to a good crash, but probably should be bigger. Pannier cross brace Happy Trails bags mounted plus new paint on tank and side covers. I had the original blue tank scanned for a color match. This tank is from a R100GS with the seat tab cut off. Cut down side cover for muffler and accessory plug added. accessory plug 1st installment hope I haven't bored anyone w/ the repost!!